Open Box Crown XTi2002 Power Amplifier Level 1


Description
You also have greatly improved control capabilities. The addition of Peak x Plus Limiters gives you full command over threshold, attack and release, and we enhanced the Subharmonic Synth so you can easily manage frequency, gain and filter type, allowing for application-specific tuning.
Plus, you'll now be able to tailor fan speed for specific applications and have software visibility of the Power Supply Temperature and AC Line Voltage. Combine all of that with integrated cast-aluminum rack handles for maximum durability and portability and you have the power to move you - and the world.


Features
- Peak x Plus Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release
- Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning
- 3 User-defined fan mode controls - normal, early and full speed - for matching fan performance to a specific application
- New system monitoring provides software visibility of AC line voltage and power supply temperature
- Integrated cast-aluminum handles for easy handling and enhanced durability
- Locking power cord clip provides a secure connection between the amplifier and power cord
- Updated HiQnet Band Manager and System Architect control software
- Increased number of presets to a total of 30; 29 of which are user definable
Specs
- Stereo, 2 ohms (per ch.): 1000W
- Stereo, 4 ohms (per ch.): 800W
- Stereo, 8 ohms (per ch.): 475W
- Bridge-Mono, 8 ohms: 1600W
- Bridge-Mono, 4 ohms: 2000W
- Input EQ: 6 parametric filters per channel with adjustable Q, ±15 dB boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ section can be bypassed.
- Crossover Filters: Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes ±15 dB bandpass gain and polarity control.
- Output EQ: 8 parametric filters per channel with adjustable Q, ±15 dB boost/cut. This 8-filter EQ section can be bypassed.
- Delay: for signal alignment of driver; 50 mS of total delay.
- SubHarmonic Synth: takes the low-frequency content of the input signal and "synthesizes" a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect. New: Users now have control over frequency, gain, and filter type.
- Peak x Plus Limiter: user defeatable limiter that allows users to control Threshold, Attack, and Release times.
- Presets: 30 total presets, 29 of which are user-definable.
- Sensitivity (for full rated power at 4 ohms): 1.4 Vrms
- Frequency Response (at 1 watt, 20 Hz - 20 kHz): +0 dB, -1 dB
- Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms): 100 dB (A weighted)
- Total Harmonic Distortion (THD): <0.5%
- Damping Factor 20 Hz to 1 kHz: >500
- Crosstalk (below rated power): 20 kHz - 1 kHz: > 70 db
- Input Impedance (nominal): 20k ohms balanced, 10k ohms unbalanced
- Maximum Input Signal: +22 dBu typical
- AC Line Voltage and Frequency Configurations: 100 VAC, 120 VAC, 220-240 VAC 50/60 Hz
- AC Line Current (120 VAC amplifier playing 1/8 power pink noise into 4 ohms per channel): 8.3A; no more than 38W at idle
- Operating Temperature: 0C to 40C at 95% relative humidity (non-condensing)
- Level: two front-panel rotary level controls, one for each channel
- Power Switch: On/Off switch applies AC power to the amplifier
- Sel/Prev/Next Buttons: three buttons near the LCD screen that are used to access menu items and front panel lockout
- LCD Screen: backlit liquid crystal display that shows preset and processing status
- Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs).
- -10 Indicator: Green LED flashes when output signal exceeds
- --10 dB below clip.
- -20 Indicator: Green LED flashes when output signal level exceeds -20 dB below clip.
- Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio.
- Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion
- Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions
- Power Indicator: Blue LED illuminates when the amplifier has been turned on and has power
- Input Connectors: XLR, one per channel
- Link/Out Connector: Loop-thru signal from input connector for linking another amplifier, one per channel.
- Output Connectors: Two Neutrik Speakon NL4MP output connectors. Channel-1 Speakon is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon connectors).
- HiQnet USB Connector: Type B, connects to HiQnet network.
- Chassis: Steel
- Front Panel: Cast-aluminum
- Cooling: Proportional speed fan with front-to-rear airflow.
- Dimensions: 19" (W) x 3.5" (H) x 12.25" (D)
- Net Weight: 18.5 lb. (8.4kg)
Featured Articles
Reviews
5
4 Reviews
0%
of respondents would recommend this to a friend
Reviewed by 4 customers
Yes!!
Verified Buyer
submitted7 years ago
bycutberto
fromundisclosed
I'm using to aDj .... and is working very good... and guitar center is a very good store ... thanks!!!
The incredible lightness of... Crown...
submitted12 years ago
byDavid Grain
fromDC Area
I have been a fan of Crown amps for many years and the worst thing I could ever say about them was that the weight to power ratio was not very good... But honestly, it wasn't very good with ANY amp... I can no longer say that... I recently bought two XTI 2k2's and put them in a rack that had one Macrotech 1200... The XTI2's are almost twice the power and less than 1/2 the weight... The amp rack with two XTI2's weigh less than the same rack with one Macrotech 1200 in it... Which, as I get older is something that is NECESSARY!! LOL Overall, I am very happy with the newest additions to my sound system... The ability to set crossovers and limiters inside the amp is very handy and also means that no longer have to carry external devices to do those things... Can't wait for the the new USBX from Crown so that I can manipulate them wirelessly from my laptop or Ipod Touch!
Exceeds my expectations
submitted13 years ago
byKAY ELDER
fromGreer, SC
My partner and I operate a musical entertainment company. Our continuing to add speakers and base bins to our equipment developed the need to add another amp. In our opinion, there is nothing like the performance of a Crown. My only complaint about setting it up for the first time is before we could plug in the cords, some strip had to be removed from the inputs. I don't remember hearing of this or seeing it written anywhere. This presented a problem at first because we thought we were going to have to get all new cords to fit the inputs. But upon careful examination, we discovered what was keeping our cords from going in.
Punchy
submitted13 years ago
bydeesh padmasenan
fromNewark, NJ
Use two of these amps to power a pair of Yamaha S215V cabinets. Run them in bridged-mono. Have been a QSC PLX guy for years, but when the PLX prices went up and the XTi prices were more in my range, I decided to give them a try. Very punchy sound compared to my PLX amps. Usually do dance music in banquet halls for 300-500 people on the floor. Never needed to come near the clip light when using the amps. The built-in processing is solid, but it leaves me wishing for easier knob control because I'm used to a separate processor. I think the XTi series gives a tight sound and they do stay cooler than my PLX amps. While my PLX amps give me more depth on the low end and hit the mid and high notes with more definition, my XTi amps are covering the room better and giving me more punch withe the dance music.
- Previous
- 1
- Next
Q&A
Have a question about this product? Our expert Gear Advisers have the answers.
No results but…
You can be the first to ask a new question.
It may be Answered within 48 hours.