[[KeywordSearchInputContent]]

4 days left for two-day holiday shipping

Item # H74111

Print this page

  1. Select the information you'd like to print out.
  2. Cancel
Radial Engineering X-Amp 500 Reamp
Use Add to Cart below to have it shipped to you, or to a store near you.
Close
  • Store
  • Availability
Guaranteed Lowest Price
Pickup In Store
GC Shopping Cart
 Cart Contents
Qty Description Price Shipping Subtotal 
      Radial Engineering X-Amp 500 Reamp (H74111)
Availability:  


Brings the magic of reamping to the masses.

The Radial X-Amp 500 Reamp is one of the eight modules designed to be comprise the Radial Workhorse Rack and Mixer System that combines the popular 500 series platform with an incredibly flexible patching system to let you create the ultimate studio environment.

The Radial X-Amp is a 500 series module that lets you take a pre-recorded guitar track and send it back to amplifiers and effects so that you can tailor the sound to suit. The advantages of Reamping are many: when recording, the guitarist need only concentrate on the performance. Working out specific sounds and optimal mic placement can be done later. This eliminates hours of tiresome repetition while allowing the producer to adjust the character of the track as the production evolves.Using the X-Amp is 'plug and play' easy to use. The design begins with an XLR balanced line level input located on the 500 series rear panel that feeds the X-Amp. To ensure the very highest fidelity, 100% discrete class-A circuitry is employed. The X-Amp unbalances and buffers the pre-recorded signal where it then feeds two transformer isolated hi-Z guitar level outputs. The ¼" jacks are front mounted for desk-top convenience and equipped with ground lifts to help eliminate hum and buzz caused by ground loops. Independent level controls enable you to adjust the drive going to each amp for optimal tone. Should one of the amps be out of phase, depressing the 180° quickly brings both in line. The X-Amp Reamper works with guitars, basses, keyboards and even voice! You can send the signal through guitar effects pedals too. In fact the only thing holding you back is your imagination.

Radial Engineering X-Amp 500 Reamp Features:

  • Active Reamp designed for 500 series racks
    100% discrete class-A electronics for best tone
    Transformer isolated to eliminate hum and buzz
    Easy access front panel jacks & controls



Radial Engineering X-Amp 500 Reamp Specifications:

  • Circuit type: Class-A discrete, transformer coupled
    Power Requirement: 40mA, +/-16VDC
    Frequency Response: 20Hz to 20kHz (adjusted for guitar signals -5dB@20kHz) - 100K Load
    XLR

    Voltage Gain:
    XLR Input to XLR Output: 0dB +/- 0.5dB
    Omniport to XLR Output: -3dB +/- 0.5dB
    XLR Input to 1/4” outputs: -0.6dB +/- 0.5dB

    THD+N:
    XLR Input to XLR Output: <0.002% @ 0dBu(20Hz~20kHz)
    Omniport to XLR Output: <0.002% @ 0dBu (20Hz~20kHz)
    XLR Input to 1/4” outputs: <0.006% @ 0dBu (1KHz)

    Noise:
    XLR Input to XLR Output: -114dB below 0dBu
    Omniport to XLR Output: -95dB below 0dBu
    XLR Input to 1/4” outputs: -98dB below 0dBu

    Intermodulation distortion:
    XLR Input to XLR Output: <0.04% @ 0dBu input
    Omniport to XLR Output: <0.005% @ 0dBu input
    XLR Input to 1/4” outputs: <0.027% @ 0dBu input

    Maximum input:
    XLR Input to XLR Output: +26dBu
    Omniport to XLR Output: +20dBu
    XLR Input to 1/4” outputs: +19dBu

    Connector I/O details
    XLR input type**: +4dB, balanced female XLR, AES standard, input impedance 1.2k Ohms
    XLR output type**: Parallel ‘thru-put’ with XLR input, +4dB balanced, output impedance 600 Ohms

    ** Typical connectors found on most 500 series racks
    OUT-1 type: Instrument-level (variable), unbalanced 1/4”, transformer isolated, impedance 3k Ohms
    OUT-2 type: Instrument-level (variable), unbalanced 1/4”, transformer isolated, impedance 3k Ohms
    Omniport type: Instrument-level input, unbalanced 1/4”, (on Workhorse), input impedance 220K Ohms
    Shipping Weight: 1.5lbs (0.7kg)
    Size: Standard 500 series rack format
    Warranty: 3 years, transferable



Radial Engineering X-Amp 500 Reamp

90 day warranty on footswitch and tubes. One year warranty on all other products.

Get your gear covered!

Now you can get added warranty protection for your new gear. Pro Coverage steps in where the manufacturer's "normal wear and tear" ends. Our PRO COVERAGE program offers you UPGRADED COVERAGE if your product ever fails!

Pro Coverage includes:

  • Accidental damage protection (new gear only)
  • Expedited Repair
  • Free Shipping (for returns or repairs)
  • 100% Coverage for Commercial Use
  • Extended Return Period
  • Extended Price Protection
  • No Lemon Guarantee
  • Free Transfer of Coverage to a new owner
  • Repair Costs Covered for up to 3 years from date of purchase
  • Repairs Can Be Authorized Toll-Free by Phone or the via the web
Voice your opinion! Be the first to review »
Questions about the X-Amp 500 Reamp (H74111)


To: GuitarCenter.com
PO Box 4769
Westlake Village, CA 91359
USA
866-498-7882
 
Order #: (if applicable)  * Denotes Required Field
*First Name:
*Last Name:
*Email:
Phone:
*Subject:
*Message:
Click to add file attachment
File Upload 5mb limit