Item # J01924

Print this page

  1. Select the information you'd like to print out.
  2. Cancel
Peavey IPR2 3000 Power Amp
Use Add to Cart below to have it shipped to you, or to a store near you.
  • Store
  • Availability
Guaranteed Lowest Price
Pickup In Store

Pickup In Store

Ultra-lightweight power amplifier provides high audio resolution and extreme efficiency.

The IPR2 3000 power amplifier is designed for years of reliable, flawless operation under rigorous use. The groundbreaking IPR2 Series utilizes an advanced design that allows Peavey engineers to dramatically reduce weight while increasing output power, reliability and thermal efficiency. IPR2 Series amplifiers are designed with a resonant switch-mode power supply and a high-speed class D topology that yields the highest audio resolution and efficiency available.

This revolutionary amplifier offers the sonic superiority and unsurpassed reliability for which Peavey is famous, in an extremely efficient and lightweight design. Advanced technology and extensive protection circuitry allow operation with greater efficiency into difficult loads and power conditions. The DDT (Distortion Detection Technique) circuitry ensures trouble-free operation into loads as low as 2 ohms. DDT protects drivers and ensures that sonic integrity is maintained, even in extreme overload conditions. The IPR2's high-efficiency design allows the amplifier to operate at very low temperatures, and does not require massive heat sinks to cool.

Peavey IPR2 3000 Power Amp Features:

  • 2-channel independent fourth-order Linkwitz-Riley crossovers
    DDT protection
    Revolutionary IPR class D topology
    Combination XLR and 1/4" inputs
    Speakon output connectors
    Two-pole combination twist lock and 1/4" (6.3mm) phone plug outputs
    Individual signal patch 1/4" (6.3mm) jacks on each channel
    Standup, LED power present indication
    Detented input controls
    1750w at 2 ohms
    950w at 4 ohms
    525w at 8 ohms
    Individual signal pass 1/4" jacks on each channel

Peavey IPR2 3000 Power Amp Specifications:

  • Rated Watts 2ch x 2 ohms: 1750 watts 20ms repetitive burst / 1450 watts 1% THD both ch. driven @ 1kHz
    Rated Watts 2ch x 4 ohms: 950 watts 20ms repetitive burst / 900 watts 1% THD / 815 watts 0.2% THD, both ch. driven @ 1kHz
    Rated Watts 2ch x 8 ohms: 525 watts 20ms repetitive burst / 500 watts 1% THD / 430 watts 0.15% THD, both ch. driven @ 1kHz
    Minimum Load Impedance: 2 ohms
    Maximum RMS Voltage Swing: 70V
    Frequency Response: 20Hz - 22kHz; +/-.05dB @ 4 ohms
    20Hz - 20kHz 2ch x 2 ohms: <0.15% @ 1,200 watts 20Hz to 3kHz, decreasing to 1,100 watts @ 20kHz, both ch. driven
    20Hz - 20kHz 2ch x 4 ohms: <0.15% @ 650 watts 20 Hz to 20 kHz, both ch. driven
    20Hz - 20kHz 2ch x 8 ohms: <0.15% @ 375 watts 20 Hz to 20 kHz, both ch. driven
    Input CMRR: > - 76dB @ 1kHz
    Voltage Gain: x 75 (+37dB)
    Crossover: 100Hz switchable 2nd order high pass and 3rd low pass per channel
    Crosstalk: > -68 dB @ 1 kHz @ 400 watts @ 8 ohms Hum and Noise: > -101.5 dB, "A" weighted referenced to rated power @ 4 ohms Slew Rate: > 12V/μs Damping Factor (8 ohms): > 215:1 @ 20 Hz - 1 kHz @ 8 ohms
    Input Sensitivity: .775 volts +/- 3% for 1kHz 4 ohm rated power, .73 volts +/- 3% for 1kHz, 2 ohm rated power Input Impedance: 15kOhms, balanced and 7.5k ohms unbalanced
    Current Draw @ 1/8 power in VA (watts): 960 (535) @ 2 ohms, 615 (315) @ 4 ohms, 400 (200) @ 8 ohms
    Current Draw @ 1/3 power in VA (watts): 2065 (1360) @ 2 ohms, 1215 (735) @ 4 ohms, 740 (420) @ 8 ohms
    Idle Consumption: 160VA, 75 watts
    Cooling: Temperature dependent variable speed 80mm DC fan
    Controls: Two front panel attenuators, crossover select switch for HPF, Normal and LPF Indicator LEDs: Five LED indicators per channel: Active, Signal, DDT, Temperature and DC
    Protection: Thermal, DC, subsonic, incorrect loads, under and over voltage
    Connectors: Dual combination 1/4" & XLR, dual male XLR input thru, two twist lock connectors
    Construction: 0.062" aluminum
    Dimensions: 3.5" x 19" x 10.5" behind front panel + 0.6" for handle
    Weight: 5.62kg (12.4 lb.* )

Voice your opinion! Be the first to review »
Questions about the IPR2 3000 Power Amp (J01924)

PO Box 4769
Westlake Village, CA 91359
Order #: (if applicable)  * Denotes Required Field
*First Name:
*Last Name:
Click to add file attachment
File Upload 5mb limit