Radial Engineering X-Amp 500 Reamp  

Item #: 
1302553613623
  • Write a Review

The Radial X-Amp 500 Reamp is one of the eight modules designed to be comprise the Radial Workhorse Rack and Mixer System that combines the popular 500 series platform with an incredibly flexible patc... Read More

Price:
$29999
Add to Wish List
GC Gear Card
Special Financing Offers
Learn More
 
PICK UP IN STORE Available in: 3-7 Days (estimated) Denver, CO (5.5  mi) Change Pick Up Store


,
SUN:11AM-7PM
MON-FRI:10AM-9PM
SAT:10AM-8PM
  • Pro Coverage Eligible
  • Free Shipping
  • Easy Returns

QUESTIONS? CONNECT WITH AN EXPERT INSTANTLY.

  • Chat Now
  • Call 866-498-7882
Overview

The Radial X-Amp 500 Reamp is one of the eight modules designed to be comprise the Radial Workhorse Rack and Mixer System that combines the popular 500 series platform with an incredibly flexible patching system to let you create the ultimate studio environment.

The Radial X-Amp is a 500 series module that lets you take a pre-recorded guitar track and send it back to amplifiers and effects so that you can tailor the sound to suit. The advantages of Reamping are many: when recording, the guitarist need only concentrate on the performance. Working out specific sounds and optimal mic placement can be done later. This eliminates hours of tiresome repetition while allowing the producer to adjust the character of the track as the production evolves.Using the X-Amp is 'plug and play' easy to use. The design begins with an XLR balanced line level input located on the 500 series rear panel that feeds the X-Amp. To ensure the very highest fidelity, 100% discrete class-A circuitry is employed. The X-Amp unbalances and buffers the pre-recorded signal where it then feeds two transformer isolated hi-Z guitar level outputs. The ¼" jacks are front mounted for desk-top convenience and equipped with ground lifts to help eliminate hum and buzz caused by ground loops. Independent level controls enable you to adjust the drive going to each amp for optimal tone. Should one of the amps be out of phase, depressing the 180 quickly brings both in line. The X-Amp Reamper works with guitars, basses, keyboards and even voice! You can send the signal through guitar effects pedals too. In fact the only thing holding you back is your imagination.

Features
  • Active Reamp designed for 500 series racks
  • 100% discrete class-A electronics for best tone
  • Transformer isolated to eliminate hum and buzz
  • Easy access front panel jacks & controls
Specifications
  • Circuit type: Class-A discrete, transformer coupled
    Power Requirement: 40mA, +/-16VDC
    Frequency Response: 20Hz to 20kHz (adjusted for guitar signals -5dB@20kHz) - 100K Load
    XLR

    Voltage Gain:
    XLR Input to XLR Output: 0dB +/- 0.5dB
    Omniport to XLR Output: -3dB +/- 0.5dB
    XLR Input to 1/4" outputs: -0.6dB +/- 0.5dB

    THD+N:
    XLR Input to XLR Output: <0.002% @ 0dBu(20Hz20kHz)
    Omniport to XLR Output: <0.002% @ 0dBu (20Hz20kHz)
    XLR Input to 1/4" outputs: <0.006% @ 0dBu (1KHz)

    Noise:
    XLR Input to XLR Output: -114dB below 0dBu
    Omniport to XLR Output: -95dB below 0dBu
    XLR Input to 1/4" outputs: -98dB below 0dBu

    Intermodulation distortion:
    XLR Input to XLR Output: <0.04% @ 0dBu input
    Omniport to XLR Output: <0.005% @ 0dBu input
    XLR Input to 1/4" outputs: <0.027% @ 0dBu input

    Maximum input:
    XLR Input to XLR Output: +26dBu
    Omniport to XLR Output: +20dBu
    XLR Input to 1/4" outputs: +19dBu

    Connector I/O details
    XLR input type**: +4dB, balanced female XLR, AES standard, input impedance 1.2k Ohms
    XLR output type**: Parallel ˜thru-put' with XLR input, +4dB balanced, output impedance 600 Ohms

    ** Typical connectors found on most 500 series racks
    OUT-1 type: Instrument-level (variable), unbalanced 1/4", transformer isolated, impedance 3k Ohms
    OUT-2 type: Instrument-level (variable), unbalanced 1/4", transformer isolated, impedance 3k Ohms
    Omniport type: Instrument-level input, unbalanced 1/4", (on Workhorse), input impedance 220K Ohms
    Shipping Weight: 1.5lbs (0.7kg)
    Size: Standard 500 series rack format
    Warranty: 3 years, transferable

Warranty
MANUFACTURER'S WARRANTY
90 day warranty on footswitch and tubes. One year warranty on all other products.


GUITAR CENTER'S PRO COVERAGE
Pro Coverage gives you added warranty protection for your new gear. Stepping in where the manufacturer's "normal wear and tear" coverage ends, our Pro Coverage program offers you upgraded coverage if your product ever fails Read More.

Pro Coverage includes
  • Accidental damage protection (new gear only)
  • Expedited repair
  • Free shipping (for returns or repairs)
  • 100% coverage for commercial use
  • Extended return period
  • Extended price protection
  • No lemon guarantee
  • Free transfer of coverage to a new owner
  • Repair costs covered for up to three years from date of purchase
  • Repair authorization-toll-free by phone or via the web
  • Customer Reviews
Loading....
You are changing the Ship-To country.

Our product catalog varies by country due to manufacturer restrictions. If you change the Ship-To country, some or all of the items in your cart may not ship to the new destination.