Behringer

collapse expand iconDescription

The Behringer Europower EP2000 is a professional-grade 2-channel power amplifier designed to deliver robust, clean power for live and installed sound applications. With up to 2,000W of peak output power, the EP2000 can drive large speaker systems at high volumes without distortion. The Class AB amplifier design provides exceptional fidelity for both music and speech.

Deliver High SPLs With 2,000W Peak at 2 Ohms

Packing serious muscle, the EP2000 puts out up to 1,000W per channel into 2-ohm loads and 750W into 4-ohm loads. Bridge the channels and you get a monstrous 2,000W at 4 ohms—enough juice to push large-format line arrays or subwoofers at dangerous levels. The amp's high-capacity toroidal transformer and massive heat sinks allow the EP2000 to crank out clean power all night long without overheating or instability.

Connect any Source With XLR and 1/4" Inputs

The EP2000 offers extensive connectivity for use with professional mixing consoles, instruments, DJ gear and more. Each channel provides a balanced XLR input and a 1/4" TRS input to accommodate both mic- and line-level sources. The Neutrik combo jacks handle everything from mics to keyboards to effects units with ease. Level controls allow you to dial in the perfect sensitivity.

Protect Your Speakers and System With Built-In Limiters and Overload Protection

To safeguard your components from damage, the EP2000 provides multiple layers of smart protection. Integrated peak and RMS limiters prevent clipping and control transient peaks. DC and thermal overload protection activate automatically if DC voltage or excessive heat is detected. The amp also guards against short circuits, faulty wiring and more. You can push the amp hard without worrying about blowing speakers.

Clean Up Your Sound With Adjustable Low Cut Filters

Unwanted low-end rumble and hum can muddy up your mix and tax your speakers. The EP2000 lets you dial in low-cut filters independently for each channel to remove distracting low frequencies. Cut off the subs and tighten up the low mids for cleaner vocals, guitars and more. You can also create a high-pass filter to optimize the amp for use with mid-high speakers.

Open Box Behringer EP2000 EUROPOWER Power Amp Level 1
Open Box Behringer EP2000 EUROPOWER Power Amp Level 1
Open Box Behringer EP2000 EUROPOWER Power Amp Level 1

collapse expand iconFeatures

  • 2 x 1,000 Watts into 2 ohms; 2 x 750 Watts into 4 ohms; 2,000 Watts into 4 ohms (bridge mode)
  • Precise Power, Signal and Clip LEDs to monitor performance
  • XLR and 1/4" TRS input connectors for compatibility with any source
  • Professional speaker connectors and "touch-proof" binding posts support most speaker wiring systems
  • Selectable low-frequency filters (30Hz or 50Hz) remove distracting infra-sound frequencies
  • Independent limiters per channel offer reliable protection against overload and distortion
  • High-current toroidal transformer for ultra-high transient response and absolute reliability
  • Ultra-reliable Toshiba/Fairchild power transistors
  • Independent DC and thermal overload protection on each channel automatically protects amplifier and speakers without shutting down the show
  • Back-to-front ventilation system including air filter for reliable operation
  • "Built-like-a-tank," impact-resistant, all-steel 2U rackmount chassis
  • High-quality components and exceptionally rugged construction ensure long life
  • Conceived and designed by Behringer Germany

collapse expand iconSpecs

Output Power:
  • 20Hz“20kHz @ 0.1% THD, both channels driven:
  • 8Î per channel-350W
  • 4Î per channel-500W
  • 2Î per channel-650W
  • RMS @ 1% THD (sine wave), bridged mode:
  • 8Î-1000W
  • 4Î-1300W
  • Peak Power, both channels driven:
  • 8Î per channel-400W
  • 4Î per channel-750W
  • 2Î per channel-1000W
  • Peak Power, bridged mode:
  • 8Î-1500W
  • 4Î-2000W
  • Distortion:
    <0.01%
  • Frequency Response:
  • At 10dB below rated output Power-20Hz“20kHz,
  • At -3dB points-5Hz“50kHz
  • Damping Factor:
    >300 at 8Î
  • Noise: -100dB unweighted, 20Hz“20kHz
  • Voltage Gain: 40X (32dB)
  • Input sensitivity: 1.15V (+3.4dBu) VRMS at 8Î
  • Input impedance: 10kOhm unbalanced, 20kOhm balanced
Controls:
  • Front: Power switch,gain control (channels 1 and 2)
  • Rear: DIP switches (10x)
  • Indicators:
  • Power: Green LED
  • Clip: Red LED, 1 per channel
  • Signal: Yellow LED, 1 per channel
  • Inputs: Balanced XLR and 1/4" TRS connectors
  • Outputs: Touch-proof binding posts and professional speaker connectors
  • Cooling: Continuously variable-speed fan, back-to-front airflow
  • Amplifier Protection: Full short-circuit, open circuit, thermal, and HF protection
  • Load Protection: Turn on/off muting, AC coupling
  • Circuit Type: Class AB complementary linear output
Power Supply:
  • Mains Voltage/Breaker: 100“120V, 50/60Hz15A
  • Power Consumption: 1600W
  • Dimensions: 19" W x 3-1/2" H x 15-4/5" D
  • Weight: 35lb.