Excellent sound controls, quality speakers, and a solid design.

View all items from this brand

The Markbass CMD 102P is a tilt-back bass combo amplifier that has a built-in Little Mark II solid state preamp to give you more power. To help shape your sound, the CMD 102P bass amp gives you a 4-band EQ, as well as VLE (Vintage Loudspeaker Emulator) and VPF (Variable Pre-shape Filter) filters for control.

The Markbass CMD 102P amp's I/O includes an input that can handle both passive and active basses, and extra XLR balanced input for double bass pickups, Neutrik Speakon Combo out jacks for use with 1/4" or Speakon speaker cables, a tuner out jack for sending unbalanced signals to a tuner, amp, or other recording equipment, and Send and Return Effect jacks to ensure your main signal continues even if something dies in your effects chain. This versatile bass combo has an angled cabinet so that you can use it as a floor model or in the more traditional vertical position. Either way, you're going to get a warm, natural sound from the 2 B&C 10" speakers and the piezo tweeter. And if you add an external cab via the outputs, the CMD 102P combo amp will give you enough sound to fill a large venue with headroom to spare.

With our Guaranteed Lowest Price, you can be assured of complete satisfaction and the lowest available price, or your money back!

Markbass CMD 102P 300/500W 2x10 Tilt-Back Bass Combo Amp Features:

Solid state Little Mark II preamp built-in to the front
2 - 10" B&C neodynium speakers
Piezo tweeter
Made of high-grade, multi-ply poplar
Glued, screwed, and sealed internally with special compounds for maximum sound quality
Lightweight
Angled cabinet design so it can be used either as a floor monitor or vertically
Grille screen to protect speakers

Little Mark II
Provides 500W at 4 ohm or 300W at 8 ohm
Gain and Master volume controls
Clip warning light
EQ includes controls for Low, Mid Frequency Low, High Frequency Low, and High
VLE (Vintage Loudspeaker Emulator) and VPF (Variable Pre-shape Filter) filters
Neutrik Speakon Combo out jacks for use with 1/4" or Speakon speaker cables
Balanced XLR out
Ground lift switch to eliminate hum
Tuner out sends unbalanced signal sent to a tuner, amp or recording equipment not needing a balanced signal
Send and Return Effect ensures main signal continues even if something dies in your effects chain

Markbass CMD 102P 300/500W 2x10 Tilt-Back Bass Combo Amp Specifications:

Speaker: 2 x 10"
Tweeter: piezo
Bass port: front
Impedance: 8 ohms
Sensitivity: 101 dB SPL
Speaker power handling: 400W RMS (AES Standard)
Frequency response: 40Hz to 18kHz
Crossover frequency: 3kHz
Dimensions: 18.9"W x 23.4"H x 18.7"D
Weight: 44lb.


Little Mark II
Power
Input impedance: 500Kohm, max. voltage: 15Vpp
Balanced Output (XLR): 22Kohm, max. voltage 25Vpp
Effect Return impedance: 22Kohm, max. voltage: 25Vpp
Output Power: 300W RMS at 8 ohm, 500W RMS at 4 ohm
Voltage is factory preset for the U.S.

Controls
GAIN —80dB to +23dB range
MASTER VOLUME
GROUND LIFT: switch on rear panel

Equalization
LOW
Center frequency: 40Hz; level ±16dB
LOW MID
Center frequency 360Hz, level ±16dB
HIGH MID
Center frequency 800Hz, level ±16dB
HIGH
10kHz shelf; level ±16dB
VPF (Variable Pre-shape Filter)
center frequency 380Hz (cut)
VLE (Vintage Loudspeaker Emulator)
frequency range 250Hz—20kHz (cut)

Outputs
EFFECT SEND
Unbalanced, max. voltage 20Vpp (pre-EQ)
TUNER OUT
Unbalanced, max. voltage 25Vpp
LINE OUT
Balanced XLR, max. voltage 10 Vpp
SPEAKER OUT
Speakon, 1/4"