Solid bass sound with tight lows.

The Eminence Legend BP102 10" Bass Speaker delivers rich bass tone with a lot of punch. Recommended for professional bass guitar applications in sealed or vented enclosures. The replacement speaker works well in single or multi-driver designs.

Use the Eminence Legend BP102 as a direct replacement speaker in the Ampeg SVT-810E, the Kustom Groove 4120, the Gallian-Krueger 4120 SBX, the Ashdown MAG 410T & MAG810T, and the Basson B410B speaker cabinets. Eminence recommends the Legend BP102 as a direct replacement in the Kustom Groove 310C, the Ampeg BA210SP, the Peavey Bam 210 combo amps.

With our Guaranteed Lowest Price, you can be assured of complete satisfaction and the lowest available price, or your money back!

Eminence Legend BP102 10” Bass Speaker Features:

Rich bass tone with good punch
Tight low-end sound
Recommended for sealed or vented enclosures
Works well in single or multi-driver cabs

Eminence Legend BP102 10” Bass Speaker Specifications:

Nominal Basket Diameter: 10", 254mm
Nominal Impedance*: 8 ohms
Power Rating**: 200W
Resonance: 35Hz
Usable Frequency Range: 40Hz-2kHz
Sensitivity***: 92
Magnet Weight: 38 oz.
Gap Height: 0.312", 7.92mm
Voice Coil Diameter : 2", 50.8mm
Resonant Frequency (fs): 35Hz
DC Resistance (Re): 5.59
Coil Inductance (Le): 0.83mH
Mechanical Q (Qms): 5.36
Electromagnetic Q (Qes): 0.47
Total Q (Qts): 0.43
Compliance Equivalent Volume (Vas): 91.2 liters / 3.2 cu. ft.
Peak Diaphragm Displacement Volume (Vd): 207cc
Mechanical Compliance of Suspension (Cms): 0.54mm/N
BL Product (BL): 10.0 T-M
Diaphragm Mass inc. Airload (Mms): 38 grams
Efficiency Bandwidth Product (EBP): 75
Maximum Linear Excursion (Xmax): 6.2mm
Surface Area of Cone (Sd): 334.5 cm2
Maximum Mechanical Limit (Xlim): 10.0mm
Mounting Information
Recommended Enclosure Volume
Sealed: 14-28 liters/ 0.5-1 cu.ft.
Vented: 25.5-62 liters/ 0.9-2.2 cu.ft.
Overall Diameter: 10.08", 256.1mm
Baffle Hole Diameter: 9.05", 229.7mm
Front Sealing Gasket: fitted as standard
Rear Sealing Gasket:
Mounting Holes Diameter: 0.25", 6.4mm
Mounting Holes B.C.D.: 9.66", 245.4mm
Depth: 4.25", 108mm
Net Weight: 8.9 lbs., 4 kg
Shipping Weight: 9.1 lbs., 4.1 kg
Materials of Construction
Copper voice coil
Polyimide former
Ferrite magnet
Non-vented core
Pressed steel basket
Paper Cone
Cloth cone edge
Zurette dust cap
*Please inquire about alternative impedances.
**Multiple units exceed published rating evaluated under EIA 426A noise source and test standard while in a free-air, non-temperature controlled environment.
***The average output across the usable frequency range when applying 1W/1M into the nominal impedance. Ie: 2.83V/8ohms, 4V/16ohms.
Eminence response curves are measured under the following conditions: All speakers are tested at 1w/1m using a variety of test set-ups for the appropriate impedance | LMS using 0.25" supplied microphone (software
calibrated) mounted 1m from wall/baffle | 2ft. X 2ft. baffle is built into the wall with the speaker mounted flush against a steel ring for minimum diffraction | Hafler P1500 Trans-Nova amplifier | 2700 cu.ft. chamber with
fiberglass on all six surfaces (three with custom-made wedges)