The Crown Xs1200 represents a new era in affordable, quality power amplification. In a uniform, rugged 2U rack mount chassis and incorporating the best of tried-and-true design principles and innovati... Click To Read More About This Product
We're sorry—we no longer carry this item.
Find a similar product below or contact us for a recommendation of a great alternative.
The Crown Xs1200 represents a new era in affordable, quality power amplification. In a uniform, rugged 2U rack mount chassis and incorporating the best of tried-and-true design principles and innovative features, the Xs1200 amp provides extensive protection and diagnostic capabilities, including output current limiting, microprocessor-controlled DC protection, circuit breaker, and special thermal protection for the unit's transformers.
Housed in a rugged, all-steel 2U chassis
Efficient forced-air fan prevents excessive thermal buildup
XLR-1/4" combo inputs
3-pin Phoenix-style inputs
Daisy-chain XLR outputs Touch-proof binding post outputs
Precision detented level controls
Five LEDs to indicate clip for each channel, power, AC mains, temperature and fault conditions
Microprocessor-controlled protection system
3-Year, No-Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications
Power Output: 2-ohm Dual (per channel) 1,600W; 4-ohm Dual (per channel) 1,100W ; 8-ohm Dual (per channel) 650W; 4-ohm bridge 3,000W; 8-ohm bridge 2,300W Sensitivity (volts RMS) for full rated power at 4 ohms: 1.4V Frequency Response (at 1 watt): 22 Hz to 22 kHz: 1 dB. Phase Response (degrees at 1 watt, 20 Hz to 20 kHz): +5, 18 Signal-to-Noise Ratio: A-weighted, below rated power: > 102 dB. 22Hz to 22kHz, below rated power: > 97 dB. Total Harmonic Distortion (THD) at full bandwidth power, from 20 Hz to 20 kHz: 0.5%. Intermodulation Distortion (IMD): (60 Hz and 7 kHz at 4:1) from full rated output to 40 dB: < 1%. Damping Factor (8 ohm) 10 Hz to 400 Hz: > 200. Crosstalk (below rated power): (1 kHz, 20 kHz): >65 dB, >45 Db Voltage Gain (at maximum level setting): 47.4:1 (33.5 dB) Load Impedance: Safe with all types of loads. 2 to 8 ohms in Stereo, 4 to 8 ohms in Bridge Mono AC Line Voltage and Frequency Configurations Available (10%): 120VAC/60 Hz and 230VAC/50 Hz.
Input/Output Input Connectors: XLR-1/4" combo connectors: One per channel, 3-pin female XLR connector and TRS 1/4" phone jack accept balanced or unbalanced signals. 3-pin Phoenix-style connectors (2-channel models only): One per channel, accepts balanced or unbalanced signals. Input Impedance (nominal) balanced, unbalanced: 20 k ohms, 10 k ohms. Output Connectors:_Balanced XLR connectors (2-channel models only): One per channel, 3-pin male XLR connector in parallel with XLR-1/4" combo and Phoenix-style input connectors for daisy-chain operation. 5-Way binding post output connectors: One pair per channel; accept banana plugs, spade lugs or bare wire. 4-Pole Speakon output connector (2-channel models only): One connector per channel. Accepts a 4-pole Speakon connector. DC Output Offset (shorted input): < 75 millivolts. Output Signal: Stereo, unbalanced, two-channel
Protection Ventilation: Flow-through ventilation from front to back Cooling: Internal heat sinks with forced-air cooling for rapid, uniform heat dissipation. Air Volume Requirements (per minute per unit): 80.15 ft (2.27 m)
Dimensions: EIA Standard 19-inch (48.3-cm) rack mount width (EIA RS-310-B), 3.5-inch (8.9-cm) height and 17.14-inch (43.5-cm) depth behind the mounting surface Weight Net Weight: 28 lb 14 oz (13.1 kg), Shipping Weight: 34 lb (15.4 kg)
3 year, no-fault parts and labor warranty on amps. 3 year warranty for most mics. 1 year warranty for Soundgrabber mic. Crown Extended Warranty available as an option.
You are changing the Ship-To country.
Our product catalog varies by country due to manufacturer
restrictions. If you change the Ship-To country, some or
all of the items in your cart may not ship to the