Crown XTi 1000 Power Amplifier  

Item #: 
  • Write a Review

700W/ch @ 2 ohms, 500W/ch @ 4 ohms, 275W/ch @ 8 ohms, 1,400W bridged mono @ 4 ohms, and 1,000W bridged mono @ 8 ohms.

The XTI Series of Crown amplifiers are professional tools designed and... Click To Read More About This Product

We're sorry—we no longer carry this item.

Find a similar product below or contact us for a recommendation of a great alternative.

Call: 866-498-7882 Email or Chat

Recommended Products

700W/ch @ 2 ohms, 500W/ch @ 4 ohms, 275W/ch @ 8 ohms, 1,400W bridged mono @ 4 ohms, and 1,000W bridged mono @ 8 ohms.

The XTI Series of Crown amplifiers are professional tools designed and built for portable PA applications. All are rugged, lightweight, and feature an LCD screen with DSP speaker presets for crossover frequencies, EQ, limiting, delay, a subharmonic synthesizer. Other features include a switch-mode universal power supply, useful function indicators, proportional-speed fan assisted cooling, XLR inputs, Speakon®, and binding-post outputs, short-circuit protection and more.

  • Integrated proprietary DSP with LCD front panel display
  • Accurate, uncolored sound with very low distortion
  • Advanced protection circuitry
  • Extremely versatile, handling a wide range of speaker impedances and outputs
  • Switch-mode universal power supply
  • Speaker presets for crossover frequencies, EQ, limiting, and delay
  • 2U rack spaces
  • Under 17 pounds
  • Speakon® and binding post outputs, XLR inputs and loop-thrus
  • Comprehensive LED status per channel
  • 3-year, no-fault, fully-transferable warranty
  • Voltage Gain at 1kHz, 8 ohm rated output:
    XTi 1000: 30.5dB _XTi 2000: 32.9dB_XTi 4000: 34.2dB

    Frequency Response: ±0.25 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms

    Phase Response (at 1 watt, 20 Hz to 20 kHz): ±15

    Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo mode, 4 to 16 ohms in Bridge-Mono mode

    Sensitivity: 1.4V

    Signal to Noise Ratio (below rated 1 kHz power at 8 ohms): _105 dB (A weighted).

    Damping Factor: Better than 500 from 20 Hz to 500 Hz.

    Crosstalk: > 80 dB below rated power, 20 Hz to 1 kHz.

    Common Mode Rejection (CMR): > 45 dB from 20 Hz to 1 kHz._Input Stage: Input is electronically balanced and employs precision 1% resistors.

    Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced.

    Maximum Input Signal: +22 dBu typical

    AC Line Voltage and Frequency Configurations Available: 100V, 120V, 220-240V _50/60 Hz

    AC Line Current:
    XTi 1000: 6.5A_XTi 2000: 6.9A_XTi 4000: 8.0A

    At Idle: Draws no more than 90 watts.

    Operating Temperature: 0 C to 40 C at 95% relative humidity (non-condensing).

    DSP Section

    EQ: 4-band paragraphic per channel, boost/cut ±12 dB. Also adjustable high and low shelving filters

    Filters: Highpass and lowpass per channel. Butterworth 6/12/18/24 dB per octave. High and low shelving filters, one per channel

    Delay: For signal alignment of driver; 5 mS total delay

    Subharmonic Synthesizer: Adds low-frequency content

    Output limiter: Prevents clipping

    Presets: 10 user speaker presets

    Front Panel Controls and Indicators

    Level: Detented rotary level control, one per channel

    Power Switch: On/off switch applies AC power to the amplifier

    Sel/Prev/Next Buttons: Three buttons near the LCD screen are used to access menu items

    LCD Screen: Backlit liquid crystal display shows speaker presets

    Signal Indicator: Green LED, one per channel, flashes when a very low-level signal is present at input

    ”10 Indicator: Green LED flashes when output signal exceeds ”10 dB below clip.

    ”20 Indicator: Green LED flashes when output signal level exceeds ”20 dB below clip

    Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio

    Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion

    Temp/Fault Indicator: Red LED, one per channel, illuminates under Fault or excessive temperature conditions

    Power Indicator: Blue LED illuminates when the amplifier has been turned on and has power

    Rear Panel Controls and Connectors

    AC Line Connector: NEMA 5-15P (15A)

    Input Connector: XLR, one per channel

    Link/Out Connector: Loop-thru signal from input connector for linking
3 year, no-fault parts and labor warranty on amps.
3 year warranty for most mics.
1 year warranty for Soundgrabber mic.
Crown Extended Warranty available as an option.

  • Customer Reviews

Review Snapshot

by PowerReviews

(based on 3 reviews)

Ratings Distribution

  • 5 Stars



  • 4 Stars



  • 3 Stars



  • 2 Stars



  • 1 Stars



Reviewed by 3 customers

Displaying reviews 1-3

Back to Top

(31 of 41 customers found this review helpful)


Thump thump

By MongoTheMadman

from Denver CO

I bought this amp to drive my single JBL JRX118S sub to enhance my rig. Now all my music 'Feels' great. I've only had two complaints while running karaoke shows and that was from neighboring businesses four doors down from where I was playing. I love the fact that I didn't have to buy a separate crossover because the features are built right into the amp. I run her bridged and will never turn it down unless there is a police escort to back up the next complainer.

(5 of 5 customers found this review helpful)


its so light

By sub sonic sound(nrg1)

from mpls

i just purchased one of these and i love it.i use it for my tops of my bigger system and for full range of a smaller one. it drives 2 mvp36 communitys and they sound crisp and clean no distortion i have had this amp full power for ten straight hours and no problems if anythign it was that my comm were getting tired from the night, and the best part of these amps is they are light i mean really light that alone should be the selling point at 18 lbs, i also got one more well the 4000 to power 2 jbl mrx 515 and with the usb plug in the back you can really take advantage of all that this amp has to offer

(4 of 4 customers found this review helpful)


Very good clear sound quality

By Big T's Karaoke and mobile Dj

from Rogersville Tn

I recently purchased this amp to put together a backup system for my mobile dj rig. I used it in conjunction with a Behringer 1832fx board as my primary setup last night for a party of about 150 people and was very impressed with the clear sound quality. I must say the sound quality is as good as my Mackie amps. No problems with clipping and the fan never came on after being cranked for 4 hours. I would highly recommend this amp, and I plan on buying a second amp soon.

Displaying reviews 1-3

Back to Top

You are changing the Ship-To country.

Our product catalog varies by country due to manufacturer restrictions. If you change the Ship-To country, some or all of the items in your cart may not ship to the new destination.