Crown XTI 4000 Power Amplifier  

Item #: 
  • Write a Review

1,600W/ch @ 2 ohms, 1,200W/ch @ 4 ohms, 650W/ch @ 8 ohms, 3,200W bridged mono @ 4 ohms, and 2,400W bridged mono @ 8 ohms.

The XTI Series of Crown amplifiers are professional tools designed... Click To Read More About This Product

We're sorry—we no longer carry this item.

Find a similar product below or contact us for a recommendation of a great alternative.

Call: 866-498-7882 Email or Chat

Recommended Products

1,600W/ch @ 2 ohms, 1,200W/ch @ 4 ohms, 650W/ch @ 8 ohms, 3,200W bridged mono @ 4 ohms, and 2,400W bridged mono @ 8 ohms.

The XTI Series of Crown amplifiers are professional tools designed and built for portable PA applications. All are rugged, lightweight, and feature an LCD screen with DSP speaker presets for crossover frequencies, EQ, limiting, delay, a subharmonic synthesizer. Other features include a switch-mode universal power supply, useful function indicators, proportional-speed fan assisted cooling, XLR inputs, Speakon, and binding-post outputs, short-circuit protection and more.

  • Integrated proprietary DSP with LCD front panel display
  • Accurate, uncolored sound with very low distortion for the best in music and voice reproduction
  • Advanced protection circuitry guards against: shorted outputs, open circuits, DC, mismatched loads, general overheating, high-frequency overloads and internal faults
  • Extremely versatile, handling a wide range of speaker impedances and outputs
  • Switch-mode universal power supply
  • Speaker presets for crossover frequencies, EQ, limiting, and delay
  • All products fill 2U rack spaces and weigh under 17 pounds
  • Speakon® and binding post outputs, XLR inputs and loop-thrus
  • Comprehensive LED status per channel
  • 3-year, no-fault, fully-transferable warranty
  • Voltage Gain at 1kHz, 8 ohm rated output:
    XTi 1000: 30.5dB _XTi 2000: 32.9dB_XTi 4000: 34.2dB

    Frequency Response: ±0.25 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms

    Phase Response (at 1 watt, 20 Hz to 20 kHz): ±15

    Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo mode, 4 to 16 ohms in Bridge-Mono mode

    Sensitivity: 1.4V

    Signal to Noise Ratio (below rated 1 kHz power at 8 ohms): _105 dB (A weighted).

    Damping Factor: Better than 500 from 20 Hz to 500 Hz.

    Crosstalk: > 80 dB below rated power, 20 Hz to 1 kHz.

    Common Mode Rejection (CMR): > 45 dB from 20 Hz to 1 kHz._Input Stage: Input is electronically balanced and employs precision 1% resistors.

    Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced.

    Maximum Input Signal: +22 dBu typical

    AC Line Voltage and Frequency Configurations Available: 100V, 120V, 220-240V _50/60 Hz

    AC Line Current:
    XTi 1000: 6.5A_XTi 2000: 6.9A_XTi 4000: 8.0A

    At Idle: Draws no more than 90 watts.

    Operating Temperature: 0 C to 40 C at 95% relative humidity (non-condensing).

    DSP Section

    EQ: 4-band paragraphic per channel, boost/cut ±12 dB. Also adjustable high and low shelving filters

    Filters: Highpass and lowpass per channel. Butterworth 6/12/18/24 dB per octave. High and low shelving filters, one per channel

    Delay: For signal alignment of driver; 5 mS total delay

    Subharmonic Synthesizer: Adds low-frequency content

    Output limiter: Prevents clipping

    Presets: 10 user speaker presets

    Front Panel Controls and Indicators

    Level: Detented rotary level control, one per channel

    Power Switch: On/off switch applies AC power to the amplifier

    Sel/Prev/Next Buttons: Three buttons near the LCD screen are used to access menu items

    LCD Screen: Backlit liquid crystal display shows speaker presets

    Signal Indicator: Green LED, one per channel, flashes when a very low-level signal is present at input

    ”10 Indicator: Green LED flashes when output signal exceeds ”10 dB below clip.

    ”20 Indicator: Green LED flashes when output signal level exceeds ”20 dB below clip

    Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio

    Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion

    Temp/Fault Indicator: Red LED, one per channel, illuminates under Fault or excessive temperature conditions

    Power Indicator: Blue LED illuminates when the amplifier has been turned on and has power

    Rear Panel Controls and Connectors

    AC Line Connector: NEMA 5-15P (15A)

    Input Connector: XLR, one per channel

    Link/Out Connector: Loop-thru signal from input connector for linking
3 year, no-fault parts and labor warranty on amps.
3 year warranty for most mics.
1 year warranty for Soundgrabber mic.
Crown Extended Warranty available as an option.

  • Customer Reviews

Review Snapshot

by PowerReviews

(based on 5 reviews)

Ratings Distribution

  • 5 Stars



  • 4 Stars



  • 3 Stars



  • 2 Stars



  • 1 Stars



Reviewed by 5 customers

Displaying reviews 1-5

Back to Top

(56 of 65 customers found this review helpful)


Nice amp with great power and light weight

By Poboy

from Texas

I just purchased two of these amps to power a couple of JBL SRX722's. Bridged mono these monsters put out 3200W @ 4 Ohms. They are so quiet and the onboard DSP is really nice. Also, the weight makes for a lighter rack which is real nice loading out. I would recommend these to anyone who wants quality and power.

(18 of 19 customers found this review helpful)


Great amp, Awesome weight


from Summerville, SC

These are awesome, their built-in DSP is a great feature for anyone who doesn't want to lug around a lot of outboard gear. I like them much better than the QSC PLX's, these push my subs/mains to be louder than the PLX's, and they still sound much clearer. Overall a great amp with a awesome weight. 5 Stars.

(17 of 17 customers found this review helpful)


Excellent built in features

By Adam

from Cincinnati, Ohio

Not sure why you'd buy anything else. Built in high/low pass crossovers, tons of options.. Load it up on your computer to get the full value out of it. Tons of power, super light-weight, and extremely versatile.

(17 of 18 customers found this review helpful)


All other amps bow down!

By gguillo

from Little Rock, AR

I am not sure if it gets much better than these amps! We use four of these bridged for (2) JBL SRX 722s and (2) JBL SRX 728s. Bridged mode @ 3200 watts @ 4 ohms is the truth! Super clean power, no noise and a damping factor of >500! The crisp highs, the clarity of the mids, and the punchiest of lows makes this amp a winner in my book! Also, it says they weigh in at 17 lbs. I think it's more around 12-13 lbs. These are very light and super easy to transport.

(1 of 1 customers found this review helpful)


Wow .. great product

By Ken Pool

from Linden, Michigan

To be honest, I wasn't a fan of crown until I purchased a crown 1200 a while back. It was ok, but nothing to write home about. This crown, however, is phenomenal! The DSP hardware is great, the amps weight is incredibly light, and the performance is very impressive. The only issue I had with the device was the manual on the user interface. It was a little cryptic when it came to running the amp in bridged mono mode. Very nice product .. I will definitely be buying another one!

Displaying reviews 1-5

Back to Top

You are changing the Ship-To country.

Our product catalog varies by country due to manufacturer restrictions. If you change the Ship-To country, some or all of the items in your cart may not ship to the new destination.