A simple solution for superior sound.

The B-52 Matrix 2000 Speaker Sound System consists of 2 - 12" 2-way speakers, an 18" subwoofer with a 3-channel amplifier, and circuitry housed in a separate compartment on the sub unit's back. A 600W amp drives the subs, and 2 - 300W amps drive the 2-ways. All of the components are matched for the best possible sound and balance with minimal tweaking. All you have to do is connect the B-52 Matrix 2000 system components, plug in the power cord, plug in your mixer or other sound source, and you're ready to go!

The B-52 subwoofer enclosure is divided into 2 separate compartments. The front chamber serves as the cabinet for the cast-frame, 4" voice coil and 18" subwoofer. The rear chamber houses all of the system's electronic circuitry, which includes the amplification for all 3 components, power supply, compressor, and preamps. The B-52 subwoofer has a power handling capability of 600W and a nominal impedance of 8 ohms.

Each 12" 2-way Matrix 2000 speaker is loaded with a B-52 custom-designed 12" woofer and a 1" titanium diaphragm compression driver, mounted to a 90<## HC deg ##> x 40<## HC deg ##> constant directivity horn. The speakers can be pole mounted, used as stage monitors, or flown with built-in 3/8"—16 TPI hardware for permanent installations. For transport, they mount onto the subwoofer's front grille.

Transporting the B-52 Matrix system is easy: Move the subwoofer onto its casters and place the included cover over the subwoofer. Next, pull the included covers over the satellite speakers and close the zippers. It is recommended that you transport the subwoofer and satellites separately. You may transport all the components at the same time by placing the satellite speakers onto the subwoofer's front panel facing down. Secure the satellite speakers to the subwoofer with the included locking strap by fastening it to the bar handles on the side of the subwoofer cabinet.

The B-52 Matrix 2000 Speaker Sound System has a limited lifetime warranty on cabs and compression drivers; 5-year warranty on speakers; 2-year warranty on amplifiers.

With our Guaranteed Lowest Price, you can be assured of complete satisfaction and the lowest available price, or your money back!

B-52 Matrix 2000 Speaker Sound System Features:

Designed for easy operation
Electronic circuitry fine tuned to match components for best possible sound
Amplifier houses all the electronics required to run the system
Speakers are designed to be pole mounted (shown with optional speaker stands)
Can sit as stage monitors
Built-in (3/8"—16 TPI) flying hardware
Comes with 3 dust covers

B-52 Matrix 2000 Speaker Sound System Specifications:

AMPLIFIER
Subwoofer power output: 600W @ 8 ohms
12" - 2-way power output: 2x300W @ 4 ohms
Line in: XLR female 
Parallel out: XLR male
Input Impedance: 48k ohm
Speaker out: Speakon NL4-style connector
Power requirement: 115V<>50/60Hz<>10A/230V<>50/60Hz<>5A
Crossover frequency: 120Hz; 24dB/octave
SUBWOOFER
Speaker: 1x18" cast-framed, 4" voice coil
Nominal impedance: 8 ohms
Subwoofer freq. response: 30 - 120Hz
Sound pressure level (1w/1m): 
Max. SPL:129dB
Weight:160 lbs.
Dimensions (Transport): 28" (W) x 35" (H) x 23" (D)
12" TWO-WAY SPEAKERS
Speaker input: Speakon-style connection (pin 1+ = +, pin 1- = -)
LF/MF woofer:1 x 12" custom transducer 
HF driver:1 x 3/4" titanium diaphragm on compression driver horn 
HF dispersion:90 x 40
Nominal impedance: 4 ohms
Active freq. response: 120Hz—20kHz 
Crossover frequency (passive): 2.5kHz, 12dB /octave  
Sound pressure level (1w/1m): ; 2kHz, 12dB/octave
Max. SPL:126dB
Weight: 40 lbs.
Dimensions (Upright): 14" (W) x 23" (H) x 13" (D)
COMPLETE SYSTEM
Weight:245 lbs.
Dimensions (Transport): 24" (W) x 47" (H) x 28" (D)